Infinite Menus, Copyright 2006, OpenCube Inc. All Rights Reserved.
Please support our sponsors
| | ||||||
| | ||||||
Please support our sponsors | ||||||
| | | | ||||
| | | ||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
| |||||||
| Building, Repair, and The Details - Tips and Tricks Talk about building, painting, covering, repairing, and tricking out your models. |
| View Poll Results: Is Y Harness for two 5955TG servos per channel Ok? | |||
| Yes, even on a 33% size 3D plane |     | 0 | 0% |
| No, must have a power distribution system |    | 0 | 0% |
| Only if power lead provided for extra servo |    | 0 | 0% |
| Dont know or not enough info provided |    | 0 | 0% |
| Multiple Choice Poll. Voters: 0. You may not vote on this poll | |||
 |
| | Thread Tools | Display Modes |
01-29-2008, 04:01 AM
| #1 (permalink) |
| Flyin' Around  Join Date: Jul 2006 Location: Tucson, AZ
Posts: 8
 |  7 channel RX Servo Allocation
How do you connect your four aileron servos, and two elevator servos to a 7 channel Rx (AR7000)? Is a Y harness OK with two Hitec 5955TG load on one channel? One for each wing and one for elevators? This leaves us with only one connector at the Rx for all pitch control. Same exposure for each aileron. I am planning to connect second Rx battery with a Y harness on the rudder channel. This is for Yak 3D 33% setup with (two) Fromeco Relion 2600 mah. Diagrams are appreciated, if you have some. Thanks for your input. |
 |
|
01-29-2008, 11:23 AM
| #2 (permalink) |
| Super Contributer  Join Date: Apr 2006 Location: Colorado
Posts: 105
|  Re: 7 channel RX Servo Allocation
Plug one elevator into channel 3 (Elevator) and the other one into channel 5 (Gear) Run a mix. Plug one Y harness into channel 2 (Aileron) and the other Y harness into channel 6 (Flaps) Turn on Flaperon wing. Not sure if it will supply enough power though. Throttle to channel 1 Rudder to channel 4 Plug power leads into channel 7 and battery. |
| |
|
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 8711 or 5955 | kim3D | General Discussions - Giant Scale | 103 | 04-02-2008 05:08 PM |
| Binding Dual RX's with DX7? | Chris | 2.4 Ghz Spread Spectrum Technology | 15 | 12-17-2007 11:01 PM |
| Hitec fans what do you think about this? | caurimare | Transmitters, receivers, servos & Navigation | 27 | 11-01-2007 12:56 AM |
| Strange AR9000 Behaviour. | bigbarper | 2.4 Ghz Spread Spectrum Technology | 5 | 08-23-2007 06:34 PM |
| 14MZ for Dummies | Kiwi | Transmitters, receivers, servos & Navigation | 281 | 10-13-2006 04:17 AM |
Linear Mode
