Giants From Down Under

[Black Sheep]

	Quote: Originally Posted by RustyTumbles
	But we still learn alot from you old blokes.

I always thought that growing old was a gradual thing -
Seems I just woke up one morning and I was OLD!

[RustyTumbles]

	Quote: Originally Posted by Black Sheep
	I always thought that growing old was a gradual thing - Seems I just woke up one morning and I was OLD!

[RustyTumbles]

Hey Richo,

LOVE ME FUTABA.....

[3dubya]

hey spocky only 12-13mm between cans you nailed it perfectly, those bolt recess are premo too master of the metal..

[TROYS PIT-BITCH]

Has anyone bought one of the Hobbycity foamies yet? Thinking of getting one, just want to know what they are like. Got rid of three of my electric models today, and going to get one good one

[Spocky]

	Quote: Originally Posted by 3dubya
	hey spocky only 12-13mm between cans you nailed it perfectly, those bolt recess are premo too master of the metal..

Hi TD,
Those photo's look good. Now I'll finished Scott's and Pete's headers the same.
Thanks,

[ThunderDownUnder]

	Quote: Originally Posted by TROYS PIT-BITCH
	Has anyone bought one of the Hobbycity foamies yet? Thinking of getting one, just want to know what they are like. Got rid of three of my electric models today, and going to get one good one

Hi Luke - Should have a Hobbycity Katana here this week so will take it to Toowoomba with me so you can have a gink at it. Wasn't sure which battery pack to order for it but will order a couple as soon as it arrives. Good to see you flying in the IMAC Comp. David.

[TROYS PIT-BITCH]

That will be good david, thats exactly was I was going to get, was going to run the 1050 3 cell Rhino packs from them too

[Talbs]

	Quote: Originally Posted by rickgell
	Nice fit out Talbs. Did you make the SWB tray mount and do the internal paint job or was the kit supplied like that?

Thanks guys , the tray mount is aircraft 12 ply, had to make it due to the gap is ment for the 4 servo tray, paint job is me just getting bored. camera flash doesn't give off the true colours but its pretty close to the out side. As i said its far from finished, will post some pics when i have done the final install and wiring.

Thanks Bronty for dropping in today and giving me a hand to do a rough C of G so i could work out a battery mounting system. To our surprise its very nose heavy at standard. Long nose moment, nice!

[Blunderbum]

	Quote: Originally Posted by Talbs
	Good stuff Blunderbum, as Cookie said they do fly nice. Still have got a good three days of work to go, but the QQ yak is slowly comming to life, got the DA one Fitty in yesterday, the last 2 biggies left, the wiring and header/ can set up. Hope to test flight next week as well ,when back off shift again. With all this wind and rain here in Adelaide i best be getting back in the shed. Hope the test flight goes well Simon Talbs

Nice work Talbs, she looking the goods. This week is looking good for test flying, Good luck for the test flight.

[Blunderbum]

	Quote: Originally Posted by 3dubya
	Nice stuff, whats the run in needle settings for the 106cs off the green run in card for that motor and ground rpm it was run up to, (ps not the default tilitson carb settings in the book). Its good to see its got that new induction block allowing it to run consistent while rich, and those things love fuel, they loose there excess power when you take it away being fussy..

Hey TD, not sure what the needle setting are meant to be and I haven't even seen any green run in card. I am taking it the Ernies to bolt it to his engine stand to run it in and pump 5 litres of fuel through it.

Are you going to bring that Godzilla down to Monarto on the 4-5 Oct for the SA champs?

[3dubya]

nar hoping to get it ready by start of November, im not much of a speed builder, i wind up doing something stuiped, towball should have his over there..