Infinite Menus, Copyright 2006, OpenCube Inc. All Rights Reserved.
Please support our sponsors
| | ||||||
| | ||||||
Please support our sponsors | ||||||
| | | | ||||
| | | ||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
| |||||||
| New to RC Modeling and Aerobatics? Wondering where to start? Find answers from our experienced crew! |
 |
| | Thread Tools | Display Modes |
04-10-2008, 05:11 PM
| #15 (permalink) |
| Doo It! Doo It!   |  Re: Funtana 100 knife edge This has nothing to do with the engine or the rudder servo (if there was blowback then the coupling wouldn't be there). My funtana pulls towards the gear in KE. It is easy to mix out. I have a 12z so I am not sure about how your programming works, but you should be able to put in a p-mix. I started with 7% up elevator with both rudder deflections and I think I ended up putting in a point or two more after that. Problem solved. |
| <--Lame Post |  |
|
04-11-2008, 12:16 PM
| #16 (permalink) |
| Gettin' Lower!   | Re: Funtana 100 knife edge here the specs. i got mine on 6 volts now. i have the dx7 but i have never done a mix to fly any of my planes i just add inputs as needed Size Category: Standard Type : Digital Torque: 72 oz/in @ 4.8v, 88 oz/in @6v Speed: .19 sec/60° @ 4.8v, .15 sec/60° @ 6v Dimensions (WxLxH): 0.74"x1.50"x1.47" Weight: 1.5 oz Bushing Or Bearing: Bearing Bearing: Single Motor Type: 3-pole ferrite Gear Type: Nylon Gear Material: Composite |
| <--Lame Post | |
|
04-11-2008, 05:23 PM
| #20 (permalink) |
| Bad-ass Super Contributer!   | Re: Funtana 100 knife edge I had a hitec HS-985. 172os of torque. Rudder needs a lot of torque. A cheaper alterrnative would be the HS-5645, however, they have a slight centering issues. It can be resolved with a programmer though. |
| <--Lame Post | |
|
04-11-2008, 06:31 PM
| #22 (permalink) |
| Gettin' Lower! | Re: Funtana 100 knife edge I have a OS 120pumped on mine, 16X4W apc prop 5645s all around on 6V and I can do nice KE but with the SFG's you can KE all day long ...The SFG's look a little goofy but it makes a big difference in the handling of this airframe (all for the better) my CG is about .25 of an inch forward. |
| <--Lame Post | |
|
04-11-2008, 06:34 PM
| #23 (permalink) | ||||||||||||||||||
| Bad-ass Super Contributer! | Re: Funtana 100 knife edge
 | ||||||||||||||||||
| <--Lame Post | | ||||||||||||||||||
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| funtana x 100 | rede2fly | Glow Powered Airframes and Kits | 99 | 03-13-2008 03:30 PM |
| Electric Shock rolling harrier landing, knife edge landing and more! | aerofundan | The Big Screen! | 3 | 02-02-2007 08:56 PM |
| Funtana X 100 ARF | Huckin' it | What's Hot! | 22 | 01-13-2007 06:09 PM |
| 106 almost cuts out in knife edge?? | baxternick | Gas Engines and Power | 25 | 12-20-2006 09:27 PM |
| Mini Funtana or Mini Edge? | ShortBus | Airframes and Kits | 6 | 05-01-2006 02:57 PM |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
