logo
Thread Tools
Old 01-15-2011, 05:15 PM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Discussion
Profile Bipe plans

Any good Profiles Bipes out there anymore? Looking for a set of plans to build from in the future and was wondering what was available and how they rate.
vsnap is offline Find More Posts by vsnap
Reply With Quote
Old 08-28-2011, 12:05 PM
Orelelbaz6 is offline
Find More Posts by Orelelbaz6
Team Aerobeez
Orelelbaz6's Avatar
Joined Aug 2011
110 Posts
it depends how big and eletric or gas but for eletrics) http://www.dwfoamies.com/index.php?o...=31&Itemid=343 or http://www.horizonhobby.com/Products...ProdID=EFL9080
Orelelbaz6 is offline Find More Posts by Orelelbaz6
Reply With Quote
Old 03-30-2012, 09:16 AM
CanCanCase is offline
Find More Posts by CanCanCase
Look, I can hover a foamy!
CanCanCase's Avatar
United States, OR, North Bend
Joined Dec 2006
361 Posts
Depends what you want to do with a profile bipe. There are Boxxers and Ultimates that pop up available from time to time. SIG is still kitting an Ultimate profile, and there are some great looking plans for a GBR50 Bipe that was designed from the ground up as a profile 3D monster.

How are your scratch building skills? ;-)

- Case
CanCanCase is offline Find More Posts by CanCanCase
Reply With Quote
Old 03-30-2012, 10:33 AM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Not bad. Any more information on the GBR50? I am not looking for a foamy or the sig kits I am talking a modern profile 3d bipe.
vsnap is offline Find More Posts by vsnap
Reply With Quote
Old 03-30-2012, 01:22 PM
chumley is offline
Find More Posts by chumley
Registered User
chumley's Avatar
Lynn Haven, FL
Joined Jul 2007
563 Posts
Quote:
Originally Posted by vsnap View Post
Not bad. Any more information on the GBR50? I am not looking for a foamy or the sig kits I am talking a modern profile 3d bipe.
http://www.theprofilebrotherhood.com...p?f=20&t=31169

I think Ron (Triflyer3D) is selling plans for about $20 (it's in the thread somewhere). The Balsa Store will occasionally run kits: http://www.thebalsastore.com/
chumley is offline Find More Posts by chumley
Reply With Quote
Old 03-31-2012, 09:00 AM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Thanks Guys I found it and the plans are on the way
vsnap is offline Find More Posts by vsnap
Reply With Quote
Old 03-31-2012, 09:54 AM
CanCanCase is offline
Find More Posts by CanCanCase
Look, I can hover a foamy!
CanCanCase's Avatar
United States, OR, North Bend
Joined Dec 2006
361 Posts
Quote:
Originally Posted by vsnap View Post
Thanks Guys I found it and the plans are on the way
They're a great set of plans. Ron does awesome work. I'm under wife-orders (you know, the kind I'm WAY worse-off if I ignore?!) to get a few of these kits out of the way before I tackle a scratch build.

You gonna post up a build thread?

- Case
CanCanCase is offline Find More Posts by CanCanCase
Reply With Quote
Old 03-31-2012, 11:36 AM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Well I could if wanted on FG. I should get the plans next week and I have all the wood on hand it would just be a matter of getting the tube, guess I should dig up the size and get it ordered. I will be doing some double cuts as I believe I will use the paper templates to make wood templates to keep on hand for later on.
Now I also found the GBR70 thread and will definitly be building a few of these up also. I inquired about the plans but they are not available yet Ron said due to some changes being made. When they due come in I will do a build thread on that plane for sure if I have time.
vsnap is offline Find More Posts by vsnap
Reply With Quote
Old 04-16-2012, 10:24 AM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Received the plans and spent a few hours reviewing them. This isnt that big of a deal for cutting, typical scratch build airplane except replace formers with the fuse puzzel. Not all bad.
One thing I realized is no matter how hard I was hoping not I would have to buy a new engine for this so I am going to go slow on the build process and work on it in my spare time. I just cant purchase a new engine at this time.
It did to one thing for me, I completely cleaned my table off and got many fatties out of the way (cant afford equipment or engines for them either for a loooong time) so I could build again. It will not go with out waste, I just need to get some measurements so I can make the engine mount wide enough for the engine I choose.

The plans are awesome and well detatiled. I am awaiting the GBR70 as I know of a person with an appropriate engine sitting idle for that one.

Scott
vsnap is offline Find More Posts by vsnap
Reply With Quote
Old 04-16-2012, 11:41 AM
joebob2 is offline
Find More Posts by joebob2
Registered User
Crestview, Fl
Joined Jan 2006
321 Posts
The GBR70 is a nice design, but it's got a lot of parts to cut. I scratched one out a few months ago and did a build thread on it over on the ProBro site. Flew well with a DLE-30, but a Mintor 38 would make it rock. Mine came out tailheavy and I had to add about 3oz to the nose for balance. You could probably cut a lot of weight out of it by going to a standard stick built fuse instead of the lite ply sides, and using balsa for the ribs.
joebob2 is offline Find More Posts by joebob2
Reply With Quote
Old 04-17-2012, 08:45 AM
vsnap is offline
Find More Posts by vsnap
Registered User
vsnap's Avatar
Brownsburg
Joined Jun 2006
2,185 Posts
Quote:
Originally Posted by joebob2 View Post
The GBR70 is a nice design, but it's got a lot of parts to cut. I scratched one out a few months ago and did a build thread on it over on the ProBro site. Flew well with a DLE-30, but a Mintor 38 would make it rock. Mine came out tailheavy and I had to add about 3oz to the nose for balance. You could probably cut a lot of weight out of it by going to a standard stick built fuse instead of the lite ply sides, and using balsa for the ribs.
I guess this was figured out already as plans are on hold till the redesign is done. When I purchased the Bipe plans I tried to get a set of the GBR70 also and he said he wanted to wait till he changed them a bit due to the balance situation.
I saw the build threads for these but really was not much said about the flying part or changes being made. It is just a really good looking profile and I am just idlely waiting for it as I cannot purchase any kits due to funds. I do however have a bunch of wood laying around waiting to beturned into something eventually.
vsnap is offline Find More Posts by vsnap
Reply With Quote



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Gallery DSC_0147 ConRadical General Discussion 0 04-11-2006 10:36 AM