Hi dudes..I am the Klown, I would like to ask other 3D pilots that use DA 150 what prop do you use.

The reason I ask is that I have used Mejzlik CF, Bolly wood, Menzs and Vess.
On all I have used 32X10. I use the 32A for the Vess.Which all are god props so don't get me wrong there.

I have found the Vess to make my engine run better and have more torque power and i see a difference in flat inverted spins, rolling circles, Water falls and many other moves.

Are you experiencing any improvement if you use the Vess? Just let me hear your experiences with all Props. I want to know if I am alone.....

Klown

I switched from a Mejzlick 32X10 to a Mejzlick 30X12 on my DA150 and MTW cans.
Spools up much quicker and seams to have considerable more pull out of a hover.
Just need to watch ripping the prop when its no loaded up.

I use the Prince "P" Tip 31x11 prop. Pull great out of a TR.

The Vess prop makes a lot more airflow over the surfaces at lower RPMs. Prop is awsome for slow high alpha flight. All the sufaces respond much quicker .

FWB

If the plane is a bit heavy, a Mejzlik30x10 is great. It lets the engine spool up immediately out of a hover.

I have been using the Vess 32A, the plane comes alive with that prop.
I have tried many props on my DA 150 with stock mufflers powered 3.3m Yak, weighing close to 50 lbs and the Vess 32A gave the best performance, didn't believe it until I tried it.

This is all good info. But I have experienced what Snap has experienced! The damn thing just runs better with the Vess 32A. The DA 150 that is...I have more power and it spools up alot faster than any others I have used.. I am flying a 3W Extra 40%. I have spent in the last few weeks 160.00 on props! They are worth it..They are really not as much as the others to tell the truth...$80.00 plus shipping..But well worth ity...But I am keeping the Prince in mind. I haven't tried that one yet. But I have the others. Any others out there?

I like my CHP 32.5 x 10

Originally Posted by Mithrandir

I like my CHP 32.5 x 10

Hi Mithrandir,
CHP huh? Tell me why if you would...I'd like to hear why. What does it do for you to run it on a DA 150 and why you are happy with it.

I know there are so many more and even 3 blades. I am trying to experiment myself.

Mejlik 30X10, and I have tried them all!

Originally Posted by flyingklown

Hi Mithrandir,
CHP huh? Tell me why if you would...I'd like to hear why. What does it do for you to run it on a DA 150 and why you are happy with it.

I know there are so many more and even 3 blades. I am trying to experiment myself.

Well... I think that it is a wider blade and maybe a little flatter... so it has decent downline breaking, I get no prop rip unless I am coming out of a dive and it pulls as well as a MENS 32 x 10 on verticals....
I have only used the CHP, a MENZ 32 x 10 and a MENZ 30 x 12 on the 250 DA150 flights in my modeling experiance... kind of a small sampling. Call Chip.. see if he has more... last October I did not see any on the pegboard in his shop....

Many of my friends are having success with the XOAR 32 x 10... I have one myself untried so far.

32a vess here

I like the vess 32 b mine pulls like crazy and will rip the prop with out throttle management. I also liked the Menz carbon 32x10. I have a 32a but was worried it would over rev the motor so I have not tried it yet.

Vess Stealth carbon 32C
DA-150 on RE3's
Awesome prop.

Well there has been some great new props developed since this thread started five years ago. I've been running a Falcon carbon 32-10 on my DA 150 since last season and couldn't be happier about switching my Mejzlik out for it. The Falcon has great vertical pull out. I can do snaps on an upline until I'm sick of them. It spools up insanely quick, too. They are very lightweight and cheaper than a Mejzlik. Hands down the best bang for the buck.