 |
 |
 |
|
|
|
|
| ||||||
|
|
|
 |
||||
|
|
|
||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
|
|||||||
04-22-2007, 11:51 AM
|
#1 |
|
Gettin' Lower!
 Join Date: Jan 2007
Location: NorCal
Posts: 46
|
Futaba 9c prorammable mixes question
Hopefully someone can refer me to a how to on the Futaba 9c programming of mixes. I have a "fully loaded" QQ Yak 54 with DA100. I am using Ailevator with elev servos on ch 2 and 8 and Flaperon mixing. I am using the curve mixes 6 & 7. Curve 7 is Throttle to elevator and it works perfectly deflecting both elevator halves (ch2/8) down slightly at low throttle for downlines. But curve 6 is my rudder to elevator mix and it only deflects the primary (ch2) elevator servo, it does not move the slaved (ch8) elev servo.... Buth my Futaba 9c users guide and instruction manual say it should operate both halves. I'm lath to use another mix here as a band aid. Thanks, Eric
|
|
|
|
04-22-2007, 01:04 PM
|
#2 |
|
That's at least a 9
 
Join Date: Jan 2006
Location: Federal Way, WA
Posts: 1,773
|
Re: Futaba 9c prorammable mixes question
Is there a chance that it's inhibited? INH on the screen?
__________________
Dan  
|
|
|
|
|
04-22-2007, 01:16 PM
|
#3 |
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Location: Lodi, Ca. USA
Posts: 1,120
|
Re: Futaba 9c prorammable mixes question
Also try hitting the link function in the mixing setup menue for that specific mix.
Garrett |
|
|
|
|
04-22-2007, 01:23 PM
|
#4 |
|
Back to the Basics!
Join Date: Jan 2006
Location: Willow Spring, NC. USA
Age: 48
Posts: 950
|
Re: Futaba 9c prorammable mixes question
I use a T9CAP.. My set up on mixes are as listed below.
P-mix 1 = RUDDER > ELEV Mix> ON MAS> RUDD SLV> ELEV LINK> ON TRIM> ON SW>B "Does not matter" POSI>NULL P-mix 2 = RUDDER > AILE P-mix 4 = RUDDER > AUX1 P-mix 5 = THRO > ELEV Mix> ON MAS> THRO SLV> ELEV LINK> ON TRIM> OFF SW> H "Does not matter" POSI> NULL I use mix 6 to set diff in elev. Use as point mix. PM me if you need more assist. I will give you my PH# Kent
__________________
Piedmont Aeromodelers www.piedmontaeromodelers.com J'Tec Radiowave www.jtecrc.com |
|
|
|
|
04-22-2007, 03:27 PM
|
#5 |
|
Gettin' Lower!
Join Date: Jan 2007
Location: NorCal
Posts: 46
|
Re: Futaba 9c prorammable mixes question
No on INH. Yes on LINK. Thanks Kent. I'll try your setup. Sounds like you do not use Ailevator but instead drive your slave elevator (mine is ch8) servo off ch2 with Pmix #6. What is the Aux1 servo you are driving in mix#4? I'll try your setup and PM you if I still have trouble. The crazy thing is I left Futaba (1024) many years ago for Multiplex and enjoyed the limitless programming capabilities for many years, I just told it what to do. Now I'm back with Futaba (for a while now) and here I am again trying to figure out their way to do it again! Why the Throttle channel drives both elevator servo's but the udder channel doesn't is pretty obscure... Eric
|
|
|
|
|
04-22-2007, 03:47 PM
|
#6 |
|
Back to the Basics!
Join Date: Jan 2006
Location: Willow Spring, NC. USA
Age: 48
Posts: 950
|
Re: Futaba 9c prorammable mixes question
I use 9 Ch. Rec.
#1 Aile #2 Elev #3 Thr #4 Rud #5 Open (Gear) #6 Aile (Flap) #7 Rud (AUX1) #8 Elev (AUX2) Activate Ailvator and Flaperon and use above mixes as needed. Sorry for the confusion. Kent
__________________
Piedmont Aeromodelers www.piedmontaeromodelers.com J'Tec Radiowave www.jtecrc.com Last edited by Downhumpty; 04-22-2007 at 03:51 PM. Reason: noted aux ch. |
|
|
|
|
04-23-2007, 10:13 AM
|
#7 |
|
Gettin' Lower!
Join Date: Jan 2007
Location: NorCal
Posts: 46
|
Re: Futaba 9c prorammable mixes question
Thank you.
|
|
|
|
|
04-23-2007, 03:37 PM
|
#8 | ||||||||||||||||||
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Location: Gainesville, TX
Age: 38
Posts: 3,557
 |
Re: Futaba 9c prorammable mixes question
__________________
Cactus Aviation http://www.cactusaviation.com/ Fromeco http://www.fromeco.org/ Free Advice: Do Not Fly In Cow Pastures! Don't Clean your Engine With oven Cleaner! Check batteries after smoke is released from throttle servo! Don't put reeds in Backwards! |
||||||||||||||||||
|
|
|
||||||||||||||||||
|
04-25-2007, 12:38 PM
|
#9 |
|
Gettin' Lower!
Join Date: Jan 2007
Location: NorCal
Posts: 46
|
Re: Futaba 9c prorammable mixes question
Well, allright, I simply switched my rudder to elevator mix from P6 to P1 and the rudder now drives both elevator halves. A simple solution to what almost seems like a software glitch. go figure. Thanks again. Eric
|
|
|
|
|
04-25-2007, 01:35 PM
|
#10 |
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Location: Gainesville, TX
Age: 38
Posts: 3,557
|
Re: Futaba 9c prorammable mixes question
good deal
__________________
Cactus Aviation http://www.cactusaviation.com/ Fromeco http://www.fromeco.org/ Free Advice: Do Not Fly In Cow Pastures! Don't Clean your Engine With oven Cleaner! Check batteries after smoke is released from throttle servo! Don't put reeds in Backwards! |
|
|
|
|
10-12-2008, 06:42 PM
|
#11 |
|
Flyin' Around
 Join Date: Oct 2008
Posts: 1
|
Re: Futaba 9c prorammable mixes question
OK, this sounds similar but not getting the same results. How do I mix two servos for 2 elevator halfs on a Fut 9Cap?
|
|
|
|
 |
 |
 |
 |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| futaba programming question help!! | hipollito | Radios | 10 | 09-22-2007 11:14 AM |
| Futaba 9C with Hitec Xtal | Jamieman | Radios | 4 | 04-30-2007 08:51 PM |
| Switching from Futaba to JR Servo Question | Nobody | Radios | 7 | 06-19-2006 03:30 PM |
| Mix help Futaba 9c | Edge 540 | Radios | 7 | 04-13-2006 10:33 PM |
| Futaba 9C - Hot to cold? | 3D-Seth | Radios | 15 | 01-08-2006 09:45 PM |
