 |
 |
 |
|
|
|
|
| ||||||
|
|
|
 |
||||
|
|
|
||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
|
|||||||
09-24-2007, 06:06 PM
|
#1 |
|
Wah wah wee wah!!
 
Join Date: Mar 2006
Location: Greensboro, NC
Age: 21
Posts: 1,612
 |
HS-5945's on 102" Yak Ailerons/Elevator?
Alright, I'm contemplating putting together a 102" QQ Yak as an upgrade from my Cap 580 that is now reduced to knife-edge-only flight. If I do, I'd really like to keep as much equipment from the Cap as possible. That would mean using Hitec HS-5945's, 2 per aileron and 1 per elevator half. Are these servos gonna cut it? The plane would be set up for IMAC and Freestyle.
I'm not going to compromise the airplane or performance, so if I really need to jump up to 5955's or 8611A's then I will, but it's going to be enough of a financial crunch just to get the 102" Yak airframe, let alone start replacing servos... RJ
__________________
Futaba Extreme Flight RC Desert Aircraft___Castle Creations Aeromodel/Hacker Brushless___Thunder Power Vess Aero B&E Graphix Higher Plane Productions |
|
|
|
09-24-2007, 06:16 PM
|
#2 |
|
I got a BIG BLOCK now ......
Join Date: May 2006
Location: Flying with the Best of Friends
Posts: 9,823
|
Re: HS-5945's on 102" Yak Ailerons/Elevator?
RJ, running at six volts you will be fine.
Donnie |
|
|
|
|
09-24-2007, 06:22 PM
|
#3 |
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Age: 24
Posts: 2,768
|
Re: HS-5945's on 102" Yak Ailerons/Elevator?
yup on 6v - and make sure the gears are good!!
|
|
|
|
|
09-24-2007, 07:23 PM
|
#4 |
|
OK 1 Roll, No I Mean 2 Point
Join Date: Jan 2006
Location: Farmington, MN
Age: 36
Posts: 941
|
Re: HS-5945's on 102" Yak Ailerons/Elevator?
5945'are good servos, check the inside of the case tops on your broken wing. Sometime the little piece of plastic that holds 1 of the pins breaks in a crash you just have to replace the top.
|
|
|
|
 |
 |
 |
 |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| QQ Yak 102" GIII | Sukhoikid | Build Threads | 118 | 06-24-2008 11:27 AM |
| QQ 102" Yak for IMAC | ben_beyer | General IMAC Discussions | 8 | 10-27-2007 01:54 PM |
| 102" QQ Yak GenIII MTW Cans/Headers on 3W106? | hpapilot | Gas Engines | 2 | 10-13-2007 12:04 AM |
| QQ YAK 54 102" | Mack | Onboard Electronics | 7 | 12-18-2006 11:51 AM |
| QQ 102" Yak finished and blinged-up!! | bodywerks | Airframes and Kits | 13 | 04-06-2006 11:14 AM |
