hanger 9 35% extra 260 ????

[kickenchiken]

So I bought the H9 35% 260 and would like to here some good building tip for useing a Da-85 and what muffler and if you think my jr8311 servos would do the job in the intire plane thanks.

[luv2flyguy]

Was looking at your profile, welcome to the hobby and the Flying Giants, I'm sure there are plenty of guys on here that can answer your questions and help you. Let us know how the build goes.

[Madd Dawg]

Are you aware that there is a problem with the wing's? contact Horizon customer service for a new set

[HANCap232G]

I got my Hangar-9 35% extra 260 yesterday and so far the building on it is going good but i am sending my wings back to horizon hobbies to get a new set so i do not have no problems with the set i got with the plane. here is a list of what is going in it.

DA-100
7 DS-8711 all the way around
Spektrum 7 Channel Radio
2 AR7000 Receivers
Sullivan Skywriter smoke system
Vess 27B Prop
Fromeco Batteries
Fromeco regulators
SWB servo arms
2 matchboxs
MTW canisters
4.5 Tru turn anodized purple spinner
2 Da Fuel Dots
DS8417 for throttle

[HANCap232G]

pictures of my 35% extra 260 & my 33% cap 580 Matt Chapman and 27% Cap 232G cowls

[krayzc]

i am hear listening......

[Chris Puckett]

	Quote: Originally Posted by Madd Dawg
	Are you aware that there is a problem with the wing's? contact Horizon customer service for a new set

There is also a notice of how to repair if you did not want to send your wings in.


http://www.horizonhobby.com/Products...ProdID=HAN1000

[mmcconville]

The repair is very easy to do BTW. FWIW, it takes longer to remove servos and rebox the wing than it does to do the repair.
One word though, it is helpful yo wax the wing tube first in case any glue seaps through the socket.

[kickenchiken]

Thanks for the pic,s. So here are some from my build.
DA-85
9 JR8711
Mejzlik 27-10th Prop
DA carbonfiber spinner
Emcotec DPSI RV Dual power Servo Interface 12CH
Fromco 5200 Batterys
Fromco regulaters
still working on the wings due to the recall on them. new ones dont evan get here till mid March.

any coments are welcome Thanks.

[Cracky]

Looking good so far, you're going to need more exit cut out for engine cooling......

Are you going to run the rudder servo in the tail or are ya making it pull-pull?

[HANCap232G]

35% Extra 260 33% Cap 580

[Bryan Mailloux]

	Quote: Originally Posted by mmcconville
	One word though, it is helpful yo wax the wing tube first in case any glue seaps through the socket.

This is very important!. The glue really expands! I almost glued my wing tube in the wing already. I even gave it a lite cote of machine oil before hand but it still stuck. The tube came loose with some coaxing.

[kickenchiken]

[quote=Cracky;376352]Looking good so far, you're going to need more exit cut out for engine cooling.....

Thanks. do you think the exit whole for the cans would be good or should I cut some more slots in it.


HANCap232G Your planes are loking good. Whish I had your shop.

[Cracky]

I love seeing build threads and seeing how people do stuff.......

	Quote: Originally Posted by kickenchiken
	Thanks. do you think the exit whole for the cans would be good or should I cut some more slots in it.

here is the cutout that I did on mine with a DA100...

I did a little build thread here:
http://www.flyinggiants.com/forums/f...ld-thread.html

[kickenchiken]

[quote=Cracky;376362]I love seeing build threads and seeing how people do stuff.......




I did a little build thread here: Build Thread
THanks but I cant pull up your build thread also can you send me a picture of the electronics on the inside thanks