 |
 |
 |
|
|
|
|
| ||||||
|
|
|
 |
||||
|
|
|
||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
|
|||||||
10-05-2008, 09:45 PM
|
#1 |
|
Whoops, too low
 
Join Date: Sep 2008
Location: Streetsville On, Can.
Posts: 75
|
Areoworks Yak and 26cc crrc Pro
Hi All
I am new to the forum from Toronto, ON area. I am planning on putting a 26cc CRRC Pro gas into a Aeroworks 120 size Yak 54, has anyone tried this plane with a 26 cc gas engine, how was it? Mike |
|
|
|
10-05-2008, 10:20 PM
|
#2 |
|
Huck Yeah!!!
 
Join Date: Mar 2006
Location: California
Posts: 1,624
|
Re: Areoworks Yak and 26cc crrc Pro
Hi and welcome to the Flying Giants. I have this plane with a Saito 1.80 and I have lots of power. A member on RCU has used a SPE 26cc with great success. He has said he has the same power as the 1.80 he used to have on it. If you go with a gas engine for this plane, I think your best bet will be the SPE 26cc. The Evolution 26 will not provide you with a lot of power, but give you enough. Below is QQ's article with his similar-sized Yak using the Evolution 26. Basically the engine provided adequate power, but did not give him the all out 3D performance.
http://www.qqaircraft.com/default.as..._page=evo73_hi
__________________
Plane: AW 50cc Extra 300  Radio: Futaba 12FG 2.4 GHz  |
|
|
|
|
02-04-2009, 06:21 PM
|
#3 |
|
Romans 8:28
Join Date: Aug 2008
Location: Freeport, Bahamas
Posts: 167
|
Re: Areoworks Yak and 26cc crrc Pro
I recently got the AW 90-1.20 and the CRRC Pro 26.I ran 10 tanks through the engine on a test bench and so far the engine is fine.I did have to change my ignition moduel,don't know what I did for that to happen.This is my first gasser.We've had some very windy days in the Bahamas lately so I just had the yak in the air for a few minutes,but the combo is great! Jody at valley view rc will be more than happy to help you out I'm sure.
When mounting the engine to the firewall I used 1/4'' spacers from valley view and 45mm evolution standoffs from advantage hobby,which gave 5 11/16''.According to the AW manual this is the required distance from the front of the firewall to the front of the engine prop hub(back of the spinner). Give Jody a call,I think you'll enjoy this combo. |
|
|
|
|
02-04-2009, 08:46 PM
|
#4 |
|
Bad-ass Super Contributer!
Join Date: Feb 2008
Location: willoughby ohio
Age: 30
Posts: 279
 |
Re: Areoworks Yak and 26cc crrc Pro
welcome to the foums. i know there a great tread on this plane on rcu under aero-works support in the the giant sacle menu. i have been looking at this plane for a quick spriing build and i will most likey go with the spe or some other 26cc engine. good luck with the plane
__________________
Energy and persistence conquer all things. Benjamin Franklin  These Colors Don't Run |
|
|
|
|
02-05-2009, 12:23 AM
|
#5 |
|
Bad-ass Super Contributer!
Join Date: Aug 2008
Location: Sunriver, Oregon
Posts: 240
|
Re: Areoworks Yak and 26cc crrc Pro
I'm planning on a MLD28 install on my 90-120 AeroWorks Yak. Any one else install this engine yet?
|
|
|
|
 |
 |
 |
 |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 26cc to 30cc engine for 73 QS YAk | randy racer | Gas Engines | 30 | 04-28-2010 04:53 PM |
| Quique's 69" yak 54 with mvvs 26cc gas engine | remie | General Discussion | 22 | 08-23-2009 10:42 PM |
| 73" QQ Yak 54 & 26cc | NUTNDUN | General Discussion | 18 | 03-17-2009 08:21 PM |
| 25% YAK w/ 26cc GAS | cyoung450 | What's Hot | 19 | 01-30-2009 11:54 AM |
| 2.6lb 26cc in a QuiQue 73" YAK!! (Revised title!) | SleepyC | Gas Engines | 115 | 09-04-2006 10:00 PM |
