 |
 |
 |
|
|
|
|
| ||||||
|
|
|
 |
||||
|
|
|
||||
| Welcome to The FlyingGiants Community! We're all about fun, and inside you'll find the greatest, friendliest, and most helpful group of people around! If this is your first time visiting, please check out site, and click here to sign up! We hope to see you soon!! |
|
|||||||
10-30-2009, 05:18 PM
|
#1 |
|
Doo It! Doo It!
 Join Date: Aug 2008
Posts: 85
|
How can I setup Futaba 7c 2.4ghz?
I want to use the following setup for my flight power system on my Futaba 7C 2.4 ghz. for my 30% Extra using 5 Hitec 7955's and a throttle servo.
Will be using 2x A123's for Rx and one 2000 NIMH for Ignition. How can I best achieve the following? - a Votlmagic battery monitor plug in (Hangtime Hobbies) - an Opti Kill switch for throttle - a redundant Rx system (each plugged into the Rx seperately) Is this too much for a 7 channel system? I was planning on Y's but not sure where best to use them. thanks in advance |
|
|
|
10-30-2009, 06:59 PM
|
#2 |
|
Riley O'Brien
 
Join Date: Oct 2008
Location: Waverly, NE
Posts: 1,899
|
Re: How can I setup Futaba 7c 2.4ghz?
Well the battery monitor is not of any use with the a123s. Hopefully they are 2 1100mah a123s for the 30% because bigger would be a lot of weight combined with a nimh for ignition. I run 1 2300mah a123 on rx(I can fly all day) and 1 1100 on ignition. Redundant rx is way overkill for 50cc in my opinion. You should be fine with 7 channels:
1. Aileron 1 2. Either elevator half one or use a eq2 or matchbox for both sides(worth the money to get a matchbox or eq2) 3. Throttle 4. Rudder 5. Elevator half 2 or kill switch or aileron 2 6. kill switch if not on ch 5 or aileron 2 7. rx power. or kill switch on a y if 5-6 are occupied |
|
|
|
|
10-30-2009, 07:23 PM
|
#3 | ||||||
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Location: High Desert California, USA
Age: 50
Posts: 5,690
|
Re: How can I setup Futaba 7c 2.4ghz?
|
||||||
|
|
|
||||||
|
10-30-2009, 07:23 PM
|
#4 |
|
Bad-ass Super Contributer!
Join Date: Jan 2006
Location: High Desert California, USA
Age: 50
Posts: 5,690
|
Re: How can I setup Futaba 7c 2.4ghz?
|
|
|
|
 |
 |
 |
 |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Futaba FASST Receiver Installation Guidelines | bax | Radios | 24 | 06-16-2008 12:15 AM |
| Futaba 7C help please. | 2robinhood | Radios | 1 | 06-15-2008 02:17 PM |
| Futaba 12Z Glider Setup | excelpoint | Radios | 0 | 01-07-2008 01:49 AM |
| FUTABA 12FG 2.4GHZ Shipping TODAY!!!!!!! | Kiwi | Radios | 1 | 01-04-2008 12:32 AM |
| Smoke Setup: How To | 3Dkid330 | Gas Engines | 1 | 05-06-2006 08:08 PM |
