logo
Posted by rmasek | 05-28-2021 @ 09:29 AM | 6,516 Views
DLE 111 all JR 8711 servos,custom painted prop
Posted by Fly shot | 05-17-2021 @ 10:35 PM | 8,417 Views
Hi guys I what to build a giant extra 300 airplane with around 200cc gas but there are too many engines options so I just one to know which ones would be the most suitables about power and trustworthy .
Posted by RedwingRC | 04-27-2021 @ 05:24 PM | 11,082 Views
RedwingRC has the new Blue Bird BLS-H71B servos with Mega Torque over 1000 oz (73kg)!!
https://www.redwingrc.com/bls-h71b-h...servo-arm.html
Posted by RWMOOR | 01-15-2021 @ 02:09 AM | 27,128 Views
Just wondering if anyone here has done a Saito Gas Conversion.
I'm sure many of you have so here goes.

I just ran my Saito FA-100 with the Morris Mini Motors Gas conversion kit. Both are brand new. Did the timing @ 30 BTDC and used marine gas w/ Klotz oil @ 20:1 ratio. Fired right up. Kept the rpm's @ 2000
for quite a while, increased to 3000 momentarily, back to idle for a while, up to 4000 for a split second, back to idle. I idled it most of the time @ 2000. Some smoke but not that much at all. Throttle transition was good as well.

So here's the result after 1 run of 1 tank (8 oz.) Engine ran fine but I noticed a lot of black soot around the muffler and upon removing it, needless to say found more of the same in the exhaust port & valve. I pulled the plug & found that coated too. Piston looks OK, just a gray color.

Is this normal or am I doing something wrong? Please advise.
Posted by arthritic thumbs | 01-11-2021 @ 01:21 PM | 26,970 Views
Hi everyone, just signed up and want to say hello. Looking to meet some fellow modelers.
Posted by DJMackND | 12-21-2020 @ 01:22 AM | 28,199 Views
JR XG11MV transmitter with DMSS/ DMS2 air module(s) wanted
Posted by tailskid2 | 12-17-2020 @ 06:23 PM | 28,625 Views
Well it flew....and flew well! Let's just hope the landing gear modification is strong enough.
Posted by tailskid2 | 12-10-2020 @ 08:25 PM | 28,000 Views
Well after a year+ assembling, sanding, glassing, more sanding my P-47 TF Giant Scale took to the air.

Sierra Retracts required a total remake of the gear section of the beautifully sheeted wing. That took a lot of time measuring, and remeasuring - and I think it worked out.

That was after I found out you can't fit the retract unit into the wing.

I don't know how many coats of primer was applied - I do like sanding -wet sanding that is. The wing came out like a starved horse.

After glassing the entire plane, panel lines were added as was rivets - too many to count. Used revets from Chad Veich - an excellent product. Also added 'panels' here and there from him.

Tried Klass Kote for paint...tried new spray gun - didn't come out too well, so much of the silver was sanded off leaving a nice primer look. That left a nice war weary aircraft that was flown by the Mexican Air Force in the 50's.

Used a DLE55 up front and it pulls the plane around just fine. Not too fast, not underpowered at all.
Posted by felisanchez1978 | 11-06-2020 @ 03:08 PM | 26,549 Views
LAST VIDEO BEFORE MAIDEN FLIGHT ON SUNDAY...
Hangar 9 Carbon CUB walkaround before Maiden flight (1 min 31 sec)

Posted by felisanchez1978 | 11-03-2020 @ 03:34 PM | 23,085 Views
Finally got the engine started and it definitely sounds really nice...it seems the plane will perform better than expected with a lot of power

HANGAR 9 CARBON CUB DLE 20RA BREAK-IN (0 min 31 sec)

Posted by Dynam RC Detrum | 10-24-2020 @ 03:12 AM | 23,155 Views
Your nitro airplanes are interested to power by electronic motor?
Your gas airplanes are interested to power by electronic motor?

Tomcat Motor G serise -

e.g. G110 replace engine displacement 1.1 cu.in (1 cu.in=16.38706cc)

check pictures as attachment

http://www.dynam-rc.cn/Product/index/id/113.html
https://www.amazon.com/s?k=Tomcat+Mo...f=nb_sb_noss_2
Posted by Carlton | 10-17-2020 @ 12:23 PM | 22,886 Views
Looking to sell my aero works extra 260. With a da 100. Excellent condition Hitec 5955 all around Asking $ 1300.00 or best
Posted by felisanchez1978 | 10-14-2020 @ 05:03 PM | 23,468 Views
I just applied some decals that I think make my Cub look more real and cool as well....scale airplanes are fun to make and this one is not the exception
Posted by felisanchez1978 | 10-05-2020 @ 11:13 PM | 24,767 Views
finished applying rivets (finally got the glue mix right), assembled the plane and it looks fantastic...also added a locking system (pretty easy) to hold the window open (not for flying though) and also got 2 videos of the lights working...

lights at night
Hangar 9 Carbon Cub lights at night (0 min 40 sec)


lights
Hangar 9 carbon cub lights (0 min 35 sec)

Posted by felisanchez1978 | 10-04-2020 @ 10:42 PM | 24,851 Views
I just glued the fuel cap assembly on both wings, the pitot tube on the left wing behind the landing light as positioned in the real plane and started to test rivets...i am trying to get the elmer's glue and water mix correct...
Posted by felisanchez1978 | 10-02-2020 @ 10:52 PM | 23,730 Views
Glued the window and now both window and door can close....i made it close tight cause some people said that the window and door tend to open mid-air.
Posted by felisanchez1978 | 10-01-2020 @ 11:20 PM | 23,678 Views
I got some details: control sticks glued and functional, removable velcro seats.

Handmade seat belt (took me 2 hours) glued and fully functional, as well as pilot ready to fly....added a life vest as souvenir in the back of the cockpit too.

throttle levers installed, seat belt mechanism, headset, flap lever ....haven't glued the right window yet....maybe over the weekend

i am planning to apply decals maybe next week and therefore making it look more scale day after day...hope you guys like it..

as you can see, i love scale details ....more details coming soon
Posted by felisanchez1978 | 10-01-2020 @ 09:25 AM | 23,402 Views
glued the door and also inside the cockpit i got a panel installed where i will install some scale things