Carlton's blog View Details
Posted by Carlton | 10-17-2020 @ 12:23 PM | 27,947 Views
Looking to sell my aero works extra 260. With a da 100. Excellent condition Hitec 5955 all around Asking $ 1300.00 or best
Posted by Carlton | 09-28-2020 @ 09:51 PM | 9,329 Views
Looking to purchase a ultra flash jet , can anyone give me some fees back on this bird ? What am getting going with the evo flash ? Also are there any build on this jet. Thanks
Posted by Carlton | 09-11-2020 @ 08:06 PM | 4,487 Views
Looking for a good battery charger 4 ports would be nice. But 2 ports would be sufficient. Looking to charge Li-Po. Lithium ion life batt.
Posted by Carlton | 09-06-2020 @ 07:16 PM | 4,515 Views
Can some one direct me to a good charger that will charge these battery packs ? Lithium ion 5200 mah , Finding the ion cube is impossible, I was using a durelite charger. But for some reason I canít seem to get to the 8.4 volts that the these batteries Are calling for. Really appreciate it, any info will be appreciated
Posted by Carlton | 08-02-2016 @ 09:44 PM | 10,971 Views
Just trying to get some advice as we as some feed back on battery chargers, I'm. Currently running Fromeco ion packs 5200 and 2800 on my yak 37.5, all I have been using is a duralite plus battery charger, pretty much plug in when the lights go out, it's all done chArging. I haven't had any problems with this set up , but is there something better than what I'm using ? Or am I ok to keep using what I have, thanks for any feed back
Posted by Carlton | 02-13-2016 @ 09:44 PM | 20,701 Views
so i have been using ion batteries since the last 12 years and have had great luck with them , but recently one of my model buddies told me i should start using A123, i ve seen these batteries in the past, but never really paid much attrention to them, but now im being told the 123 are far superior than the ion, just wanted to hear from some of the giants fan, what are u guys running, any imput would be appreciated, im mainly flying 40% planes
Posted by Carlton | 01-04-2015 @ 09:14 PM | 12,092 Views
Just seeing if this is normal, I'm flying a 37.5 pilot rc yak 54. I'm running a da 170 with cans, plane fly great, but when the motor is at idle, the vibration seem strong, everything is tight. Is this normal ? My da 100 on the extra 260 don't put out that kind of vibration. Thanks guys
Posted by Carlton | 12-25-2014 @ 08:25 PM | 10,658 Views
Well I don't have a balancer big enough to balance my yak 37.5, Can someone give me some suggestions thanks
Posted by Carlton | 11-18-2014 @ 09:42 PM | 15,248 Views
OK guys here is my problem, im flying a 37.5 pilot rc yak 54, Im running a Da 170 with cans, plane seems to fly ok but i notice that i have to carry 3 clicks of up elev to maintain level flight now when i flip to inverted the plane wants to climb under power is this a thrust issue ?
Posted by Carlton | 10-24-2014 @ 10:07 PM | 13,199 Views
Does any 1 know whats going on with red aero mega pilots? if not are there any where where i can find some decent pilots,
Posted by Carlton | 10-11-2014 @ 11:58 PM | 10,738 Views
Can someone please show me how they set up there tail wheel assembly ? im trying to use the CF tail wheel assembly that came with the kit, but man im having a hard time getting any real movement from the rear wheel. i tried changing springs but still no improvement, i see some guys are using a tiller set up but my plane came with springs, any help will be appreciated
Posted by Carlton | 10-05-2014 @ 10:49 AM | 11,635 Views
is there anyone running the stock baffle that was suppplied with this kit ? does it help? is it needed, will the engine be ok without it, ? hole was cut out on the lower cowl plus im running cans,, so the whole back end is pretty much open thanks
Posted by Carlton | 10-03-2014 @ 09:53 PM | 11,689 Views
Well im looking for a trailor to haul these big 40% planes, any ideal where i can locate one? if it could be at few inches shorter that would be great thanks Carlton
Posted by Carlton | 09-27-2014 @ 10:57 AM | 10,480 Views
Just a quick question, would form a Gasket sealent be sufficent to use when installing my headers using a da 170 running cans thanks
Posted by Carlton | 09-22-2014 @ 09:36 PM | 10,677 Views
Can anyone tell me what that nipple on the front of the da 170 motor is for? should it be pluged or is it ok the way it is
Posted by Carlton | 09-16-2014 @ 10:36 PM | 11,053 Views
Does anyone know where to find servo hardness where you couple all 3 wing servo to your smart fly? i know thunder bolt Rc sells them, but man they are in canada, and they are saying up to 2 weeks before shipment arrive, are there any one within the state that sells these thanks
Posted by Carlton | 09-14-2014 @ 07:11 PM | 11,409 Views
Just installed 12 Hitec 7955 on my 37.5 yak, i was able to program all servos through my smart fly EQ 6 turbo reg, as i was going around to just double check all before 1st flight, i notice that my rudder is having a constant movement, upon further digging i can see the rudder servos having crazy jitter, have any one experence having this problem? i am running 2 7955 gang together. any coment or ideal is well needed thanks Carlton
Posted by Carlton | 08-16-2014 @ 11:39 PM | 14,653 Views
Are there any one flying the pilot yak 54 37.5 running smoke ? i was trying to put both tanks side by side, after i was all done i notice that there is a wing bolt that sits in the same location as the tank, kinda stuck, any one ran into the same problem? any help would be appreciated thanks
Posted by Carlton | 08-10-2014 @ 06:42 PM | 15,002 Views
Any one running a da170 on there pilot yak 54 37.5 ? can u please tell me what length stand off i need ?
Posted by Carlton | 07-19-2014 @ 09:54 PM | 16,821 Views
Are there anyone running Da mtw flex headers for the 170 with the large pro flow cans?

can u please tell me what size mm coupler and clamps are needed thanks