logo
Posted by nzflyer21 | Today @ 12:21 AM | 17 Views
Hi again, well not much more completed this weekend, a bit of a disaster really, my son arrived with his lovely french girl for the weekend which was very nice. But my son had a project in mind to complete and as the weather was not that flash or warm ,he decided to build his cabinet in the garage.
It turned out to be a very dusty affair, pretty much covering everything in a coat of dust!
So I have spent the last few days cleaning and getting everything back to square one againl
About correctly mounting servos
.
I looked up about how to use the servo eyelets properly, I remembered reading a while ago that the eyelets go to the bottom of the servo. I have done this no, it does seem to make a difference, they feel more secure now
Is this correct?
What are your thoughts on this ? Any comments would be welcome.

I added extra support to my servo rails by placing and gluing some small plywood supports over the top of the rails. A bit of added security.

.
Posted by Vtach688 | Yesterday @ 09:36 PM | 30 Views
So I was out of RC for around 8 or so years, and got back into in last year. I started out slow with a EF Timber then progressed to my latest airplane.
When I left RC, my highest achievement was a Aeroworks Yak 54 50cc. Having a collection of electric airplane, I felt I was missing something. Yes, it was a gasser, lol. So I recently acquired a Dave Patrick Edge 540T, 30cc-ish, 78" wingspan plane. I got it a good price and it was a minimum buy in.

It's not new and has had a repair, but still good bones. I had a DLE 55, so that 's what I installed. This is plane looks bigger than a 30-35cc airplane and not much heavier than the 35cc. In fact, she came in at 15.lb.

My plan is to fly it, if i like the it, then i'll do a restore and recover job. its like finding that classic car, i guess.

I would like to see if anyone have an info on this bird. Like the actual specs, CG, and so on. It's not fully needed but the information would be nice.

I'll also update this as i go along and post the video on my YouTube channel ( I'll put a link below). thanks for checking out the blog,

V.



Father's Day at MARKS (4 min 22 sec)

Posted by dexcraft | Yesterday @ 12:49 AM | 64 Views
Shop super strong and diverse carbon fiber composites for a multitude of applications, in areas ranging from automotive to marine, etc. We are committed to provide low priced carbon fibre sheets, pre-preg and autoclave composites.
Posted by nzflyer21 | 06-21-2019 @ 04:55 AM | 212 Views
Hello there, I haven't got much completed over the last few days. The weather has turned really cold, we have had several big frosty mornings in row and by the time I get home from work there is only about an hour's light left and the temperature drops really quickly , making it to cold to be out in the workshop.

I positioned my large Hi-Tec servos where I felt they should go.which ended up being further back then I wanted. The plans don't give any clues as to where they should go,but still should be just ahead of the CG.

I am planning on a pull pull system for the rudder and elevator at this stage.
Also planning on doing a bit of scale detail in the cockpit, so have been thinking about overall accessibility to make sure I can get to the servo positions if needed once the plane is completed.
Posted by woodendesk | 06-19-2019 @ 10:41 AM | 344 Views
Well I've moved in officially!! Here is the first shot of the 4 car garage and shop I have going for me now. Comment any suggestions you may have to making it more friendly, fun, enjoyable, etc. I have a full fridge and freezer in there too for libations! Also a full bathroom in the garage!!
Posted by nzflyer21 | 06-18-2019 @ 02:08 AM | 351 Views
Hi there
I thought I would add a few pictures of the fuselage progress for the 1\3 rd scale Morane Saulnier.
I have spent abit of time working out the engine position and servo position s for the throttle and choke on the Moraine Saulnier the fuselage progress to date seems to be going along nicely. When I started to look at this model ,there seemed to be limited construction pictures online. Maybe I was looking in the wrong places.
As I mentioned earlier this is my first adventure into gas engines so lots to find out about them..
Anyway just wanted to say hello again.
Posted by nzflyer21 | 06-16-2019 @ 08:41 PM | 425 Views
Hi there, just wanting to introduce my self today, I am pleased to have found this web site, I have found lots of interesting topics and ideas.
I love reading all the tips and great ideas on offer and have made use of some of them. I have always flown with glow engine and now I have started my first gas engine product, A Balsa USA Morane Saulnier 1/3rd scale.

I have built the 1/4 scale Fokker DVII from scratch, it is yet to fly. Very busy at work at present so it will have to wait.

I will pop a picture on today for you to see, I have tried to give it some weathering effect to give that a go.
Posted by RAF | 06-14-2019 @ 07:30 AM | 536 Views
Posted by woodendesk | 06-10-2019 @ 08:06 AM | 901 Views
3DHS YAK 55M 91inch
*More to come....Here is what I see just on the surface the Yak has. I will update as I go along going over the plane. Consider this also documentation of the Yak, servicing, modifications. As most of you know I love to be thorough.
SERVOS________________________
-Rudder: (Hitec) HS-7955 TG (Titanium Gear) (X1) 4.8-6.0V programmable
-Elevators:
-Ailerons:
-Throttle:
SWB servo arms

ENGINE_________________________
-DLE 60cc Twin
-Falcon 24 X 9 (Gas Carbonfiber Propeller)
-Fortitude Fuel tank (20oz./V.2)
-EASY PULL fuel dot (silver)


ELECTRONICS___________________
-Fromeco Wolverine power switch
-Tech Aero Ultra IBEC (ignition battery elimination circuit) 5v-6.6v
-Spektrum receiver

BATTERIES______________________
*TBD- I haven't decided what route I want to go here.
Posted by TexasFlyBoy | 05-19-2019 @ 07:25 PM | 1,831 Views
This may be my favorite plane.
Posted by TexasFlyBoy | 05-19-2019 @ 07:10 PM | 1,847 Views
Slow pass at Loomis Flying Field, Mooreland, OK. August 2017
Posted by woodendesk | 05-13-2019 @ 11:32 AM | 3,392 Views
UMX BEAST:
Modifications______________________
- Metal prop shaft
- Carbon fiber Battery tray to accommodate larger batteries (I custom made)
- Mt propeller logos (Callie Graphics)
- Carbon wheel pants (I custom made)
-Carbon Landing gear struts (I custom made)

Future add-ons_____________________
- CASS display laminated
-Adding custom made foam pilot bust
- clear custom servo covers
- possible upgrade to 3S (still considering it)
Posted by Midwest_tuna | 05-12-2019 @ 05:57 PM | 2,196 Views
I just completed the build of a PAU Sukhoi. Part of that build was the installation of MKS 777A+ servos on all the control surfaces. Upon completion of the installation I noticed a slight flutter in the elevator servos particularly when I switched from high rates to low rates or if I moved the trx sticks rapidly. After consultation with the techie at MKS he advised that the problem was caused by poor quality servo extensions even though the extensions used were heavy gauge. The issue is not the gauge of the wire, rather the alloy of the steel contained therein. This becomes increasingly important as the extensions get longer such as elevator servos in the tail of the plane. Today’s high frame rate high speed servos require a very clean signal, especially when Spektrum Power Safe receivers are in use. Additionally, Spektrum recommends that signal boosters not be used. MKS recommend the use of a superior quality servo extensions such as the ones offered by Power Box systems. I ordered them from Horizon (available also from Chief Aircraft), installed them on the elevator servos and the servo flutter problem went away. I am now in the process of replacing the wing servo extensions with Power Box (German made) extensions.
Posted by Greg Briley | 05-10-2019 @ 01:48 PM | 2,213 Views
I found a new use today for that real cool sticky tape I was selling. For twenty year I never had a problem with mice. A nasty neighbor moved two doors down from me and now I have mice. You would have to see to believe. I stapled down a 12 by 16 piece of that stuff . and sure enough caught a mouse the first night. It sticks to there feet first and then the fur has no chance. After selling all that I had I was able to find it at Home Depot in a different size. Its called Bondera. I first used it for Batteries and gas tanks along with remote receivers. Thanks just had to share that
Posted by jj flyer | 05-09-2019 @ 12:39 PM | 2,249 Views
i'm new to this site. Could you please tell me how to enter a classified ad?
Thank you
John,
Posted by bravo56 | 05-04-2019 @ 09:53 AM | 2,467 Views
Hi Guys,
Been flying RC since 1980. I belong to the Lorain County RC club Here in Elyria, Ohio
I just bought a Hanger 9 Waco and am looking forward to flying it.
Posted by AGFrc | 04-22-2019 @ 10:15 PM | 2,996 Views
AGFrc A80BHMW super torque waterproof steel gear digital servo will be the great option which support to use with high voltage and damp situation. A80BHMW servo make almost 500oz-in torque with speed 0.11sec at 7.4V. While using voltage up to 8.4V, it can deliver 555oz-in super torque and 0.085sec high speed at 8.4V.

This A80BHMW is waterproof IP67 level up to 1 meter which allow driving in the rain, puddles, snow and mud. High reliable and durable patent gear design which can be longer service life. Full aluminun CNC case for fast heat disppation. High precision digital control circuitry.

Perfect for scale crawlers, 1/8 1/10 monster truck, 1/8 1/10 2WD and 4WD buggies, as well as 1/8 scale buggies and trucks. In addition, this A80BHMW is great choice for boats and other application which require high power, high voltage and waterproof servo.

Specification
A80BHMW
Operating Voltage: 4.8-8.4 V
Operating speed: 0.120sec/60° @ 6.0V
Operating speed: 0.100sec/60° @ 7.4V
Operating speed: 0.085sec/60° @ 8.4V
Stall Torque: 31 kg-cm (430.51 oz-in) @ 6.0V
Stall Torque: 36 kg-cm (499.95 oz-in) @ 7.4V
Stall Torque: 40 kg-cm (555.50 oz-in) @ 8.4V
Gear: Steel
Motor: BLS
Size: 40*20*37.2mm (1.57 x 0.78 x 1.46 in)
Weight: 79g
Connector Wire: JR 300 mm

More details about this servo, check here
https://www.agfrc.com/index.php?id=1987