|
|
|
Re: New Equalizer 10 Announced
Bob will not be at Toledo this year. If you call them at 480 460 2652, you can order the unit. His website will be updated soon.
|
|
|
|
Joined Dec 2006
715 Posts
|
Re: New Equalizer 10 Announced
|
|
||
|
Re: New Equalizer 10 Announced
Quote:
I have all my planes setup this way and some are two plus years old and the plugs snap together like day one. If your worried there is also a safety clip you can glue in place so the plugs wont ever come apart unless you lift the tag. Let me go look on the web for some links. Kiwi |
|
|
|
|
Re: New Equalizer 10 Announced
http://www.hobby-lobby.com/connectors.htm
Go down the page and look for speed 400 connector. I dont see the safety clip on that page but they come in black. My plane is 1000 mile away tonight so no pics of the way I set up the plug until I get there on Saturday. Kiwi |
|
|
|
Re: New Equalizer 10 Announced
http://www.modelspot.com/mpx/leads.htm
check it out - this best quality plugs and leads ever!!!! Kiwi that plug is called a multiplex plug. |
|
||
|
Re: New Equalizer 10 Announced
Quote:
are those aerials at 90 degrees to each other? hard to tell in the photo - the one on the left could be pointing up a bit. |
|
|
|
|
Re: New Equalizer 10 Announced
Doc,
I'm far from my toy at the moment but help me clarify this. Are they saying that one antenna should be vertical and the other horizontal. What I mean by that is each rx has two antenna so to speak so I bend the wire on the right side of the Rx up to 90 degrees and the left one i leave at 270 degrees or flat so to speak. Then with the small satelitte antenna I do the same. I was going to mount it down the side of the frame so it was at 90 degrees to the receiver antenna. I did not understand or read the book well enough either, I must admit, to see where that was what they were hinting at regarding antenna placement. Some if you have it setup post a photo of those tiny little wires to make it clear whats the best recommended antenna setup please. Kiwi |
|
|
|
Re: New Equalizer 10 Announced
It's on the website now. Looks like a good deal. Might have to get one.
Jay |
|
||
|
Re: New Equalizer 10 Announced
Quote:
|
|
|
|
|
Re: New Equalizer 10 Announced
I think those Graupner/Multiplex plugs are a PITA to solder on. I like to use 4 pin Mini Deans connectors for two servos (+ and - together on two pins, signals on other two), or a 3 pin Mini Deans for the signals and a Full Size Deans for the power on three servos. The Mini Deans and the Full Size Deans give an extremely positive connections and would not come apart in the air unless the wing or stab departed the air frame.
|
Currently Active Users Viewing This Thread: 3 (0 members and 3 guests) | |
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
EQ 10 and X9303 | Flyinrazrback | Onboard Electronics | 7 | 01-25-2008 07:48 PM | |
Bringing a 10 years old 3W 44% Ultimate back to life | xtdsm | Airframes and Kits | 32 | 11-05-2007 01:21 AM | |
Just ordered 10 sheets of depron | ilovemetro | Foamies | 3 | 05-18-2007 06:13 PM | |
Thistledown Fall Festival Fun-Fly -- Sept. 8, 9, and 10, 2006 | jdetray | Event Announcements and Discussion | 168 | 09-24-2006 07:03 PM | |
another top 10 list! | crazyextra | Humor | 2 | 03-09-2006 07:14 PM |