|
|
United States, AZ, Phoenix
Joined May 2010
407 Posts
|
Slipperymick3d, Thanks I appreciate the time and experience. I have read that the 215cc is a bit heavy when it comes to balancing the plane. It sounds like for most things being equal minus preventative maintenance, both planes are closely aligned. Thanks again.
|
|
|
|
|
my DA170 with muffs is tail heavy with pilot , its cg is right on tube center or up to 1" aft
|
|
|
|
New aircraft maiden day. CARF Extra330LX 3.0m; GP178; JMB TRA70L canisters; MTW knuckle headers; 6” TruTurn; Falcon 31x12; 5” White Rose mains; White Rose/J&J tail wheel hybrid; Hitec 9380 flight controls.
New engine ran nice and cool and was left a bit rich on both needles as I break it in, ImagesView all Images in thread |
|
|
|
looks beautiful!
congrats! would you be willing to share with us: 1. what is weight with fuel tank empty 2. how was flight envelope? 3. can you set up mechanical servo for the elevators so that with full servo travel, there is only 15 degrees of elevator travel in any direction? meaning, for IMAC, low travel and high servo resolution? |
|
|
|
Aileron hinge pins 330LX
|
|
|
United States, AZ, Phoenix
Joined Oct 2019
30 Posts
|
Graphics being applied
|
|
|
United States, AZ, Phoenix
Joined May 2010
407 Posts
|
Is there enough room for Tune Pipes in the 330XL?
|
|
|
Joined Jun 2015
133 Posts
|
|
|
|
United States, AZ, Phoenix
Joined May 2010
407 Posts
|
Thanks for the response! Good information. Will stick with cans then.
|
|
|
United States, AZ, Phoenix
Joined Oct 2019
30 Posts
|
Did these fit in there without cutting the cowl at all? Just got a set from JTEC and mounted them to my GP 178. I haven’t cut the cowl yet, but it looks like it’s going to be a tight fit... really hoping I don’t need to cut the half moons!
|
|
|
|
mine were rubbing so I removed a shim from motor mount and it still made contact. took them to the local fab shop and had them angle the end plate for clearance
|
|
|
Joined Jun 2009
37 Posts
|
Hi Guys,
The first kit has arrived just yesterday from the 2. After the first quick check overall the kit made a good impression on me, however I found some of the factory solutions less reliable. By this I am asking what is your experience, mainly those owners who made enough starts which after the regular week points could come out. One is the fixation of the canopy. Somehow I could stay at the one screw on top solution howeverI found that the canopy frame could move a lot in sideways which after a point in my eyes could results that fixation screw get loose even at worst case. Here I am thinking of to rework the front flaps of the canopy frame into a screw lock version, by that at 3 points the canopy would be fixed with screws. The other is that the mounting point of the rear landing gear is located on the removable door of the fuselage. I cannot imagine this can withstand example harrier landings. I am thinking of to glue a wooden inlay a bit more forward which can be used to mount the rear landing gear. What is your opinion, or what do you see to make differently if you could build once again this kit? Cheers, Vince |
|
|
|
did just that , removed (dremmel) the original wood tab in the tail box then hysol a FG flat plate to engage fuse and T wheel mount screws
I place a piece of tape over the screw hole before flight to prevent loss , and use a longer screw |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |