|
|
|
Yup.....I tried the GP ignition (GP 176) with my onboard A123's through a Tech-Aero IBEC......kicked back so hard it threw my start/stick 30' & ruined a 32" prop......just cough/up another $85.00 for a RCexl ignition & the issue goes away.....
|
|
|
|
|
I have a GP 123, I run 2S lipo I had an original Tech Aero feeding it 6.6V it never kicked back always started easily. I probably prevented kick back running 100LL avgas. I purchased the new HV TA IBEC and running it now on 8V, it may be my imagination but engine seems to run a little better.
|
|
|
Des Moines, Iowa USA
Joined Nov 2007
7,494 Posts
|
|
|
|
|
One step closer towards a move to 12v flight systems. For years the standard was 4 cell nicads at 4.8v. Then we all went to 5 cells at 6.0v. Next was the move to LiIon and Life at 6.6 volts. Then 2S lipos at 7.4-8.4 volts. Already 12 volt servos are coming out and I'm seeing receivers and ignitions rated at 12 volts. In a couple of years we will all be running 3S lipos on everything at 11.1 volts then it is only a matter of time before people push that to 14.8v 4s systems.
|
|
||
United States, OH, Berlin Heights
Joined Jul 2006
5,961 Posts
|
Quote:
Rite that will work for you,because you will never fall below 6.6.I just don't like the special care needed for lipos and the risk of fire.The majority of members at my club fly electric and the majority have had a fire.Some due to chargers not shutting off,others never new why.Hell I probably voided the two year warranty,just for switching ignitions,after reading the manual.I don't know why GP just doesn't use a ignition rated for 6-12 volts.One more complaint is both mufflers have a pin hole leak in the bead of weld at the manifold flange. |
|
|
||
|
Quote:
|
|
|
||
United States, GA, Statham
Joined Apr 2015
720 Posts
|
Quote:
|
|
|
||
|
|
United States, OH, Berlin Heights
Joined Jul 2006
5,961 Posts
|
On the positive side when I change ignitions and check the timing it was dead nuts on 30* BTDC and had room to adjust either way.Engine seems to run fine at factory settings,going to get some flights in before twisting the needles.
|
|
|
United States, OH, Berlin Heights
Joined Jul 2006
5,961 Posts
|
Has anyone notice how much the used DA70's have drop in price sense the GP has hit the streets.
There was a time a used DA would sell in hours the first day for 700 bucks.Now they set for a while at 600,and there are more showing up everyday for sale. I'll be the first to omit that I pulled a perfectly good running DA off and replaced it with a GP just to see how they compared to DA.I must say it was a direct bolt on replacement for the DA,standoffs and mounting bolt pattern,exhaust exit tubes all were the same.It did weigh more,my scales showed a 4ozs. more for the GP.That was with both engines with mufflers. |
|
|
United States, OH, Berlin Heights
Joined Jul 2006
5,961 Posts
|
You know for me I didn't give up any rpm's,at lease I think.My DA will do 7450 with a falcon 24-9.Seems that some will do around 7250,I guess it's just the luck of the draw.I haven't even got a flight on mine due to weather,and to new to bother with a rpm reading,just two tanks of fuel.
Time will tell if the 76 will be like the 123 or turn out like the 61. |
|
|
United States, AZ, Lake Havasu City
Joined Mar 2015
379 Posts
|
It seems that the GP123 ignitions need at least 7.0 volts for them to work reliably. This is based on information from our customers. We have changed several X24's so that they output either 5.0v or 7.0v (instead of 6.0v) just for these applications.
|
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
Thread Tools | |