|
|
|
Re: "The New" AreoWorks 50cc Edge
Brian,
WoW where have you been?..hope it was some where warm with sand, umbrella drinks & women in bikini's every where!..LOL I looked over Deitrich Aircraft scale Red Bull Racing 50CC Edge 540 When i was in the market for a 50cc but i like the Areoworks one better! So i bought it! First off i wanted a green plane since the EG mx-2 came out and i wanted an edge..it was an easy decision! mannyh |
|
|
||
|
Re: "The New" AreoWorks 50cc Edge
Quote:
Set-up will be: BME 58 Es Compisites pie 55 14" header JR 8611a All Around Futaba 9157 on the rudder Futaba FSST 6014 Duralite lith-magiunese Duralit reg swithes Mejlik 23x8 A few odds % ends spinner ECT..ECT Can't wait to get her finnished! mannyh |
|
|
|
|
Re: "The New" AreoWorks 50cc Edge
You will love the BME 58. GREAT power, and a smooth runner to boot.
|
|
|
|
Re: "The New" AreoWorks 50cc Edge
I have a DA ready to go in. I am ordering 7955s all around. I am trying to decide on a canister or the standard muffler that I have. I think the KS can would be a good addition to this plane but it's a couple hundred more.
|
|
|
|
Re: "The New" AreoWorks 50cc Edge PICS
Wow this plane flys smooth! I photographed a club members maiden with this edge, its a floater when you want it to, and hauls it you want. and flat out looks cool. He toned the ailirons rates on low down as I recommended, well worth it as its has big surfaces. Makes me want one my self. heres the pics, I am sure video will be taken soon. more photos when we have better weather
mike |
|
||
|
Re: "The New" AreoWorks 50cc Edge
Quote:
Also, how did the balancing go. The 3w is on the heavier side, but with rudder servo in the back, It might be ok. The bme, I have no clue. Its so light, all the bats will be up front as much as possible??? Don. |
|
|
|
|
Re: "The New" AreoWorks 50cc Edge
The DPA Edge looks nice. However, after owning their 42% Slick, I'll never buy from them again until they dump World Models as their manufacturer. The quality of the plane was the worst in any giant scale model I've owned.
|
|
||
|
Re: "The New" AreoWorks 50cc Edge
Quote:
Don, LOL!!!..i havn't even started on this build yet...been super busy with work the last 2mths and don't feel like building just yet I know, I know lame excuse..this next couple weeks or so i'll start..we just got dumped on by 6" of snow, so i can now consider it a winter build. The only thing to get is the header. Check this thread out! i started it the same time this one ..a good friend of mine bought his the same time..went with the same engine..he's done his, Razzing me about how slow i am..LOL http://www.rccanada.ca/rccforum/showthread.php?t=94597 mannyh |
|
|
|
|
Re: "The New" AreoWorks 50cc Edge
Thanks,
lol, Your right, your freind is razzing you prettygood... He did a good job on his edge. I really like the way the BME58 head dont hang out the bottom of the cowl. Looks better that way... Don. |
|
|
|
Re: "The New" AreoWorks 50cc Edge
I agree with the cylider head as,looks better tucked inside. Jack's a great builder,with sweet idea's when it comes to finding the right spot in a tight place for mounting stuff.And even better at razzin'...LOL! The New AW planes come out a little porky so the 3w is a good choice it that regards,but the BME on a pipe is no slouch either..it's just the balance issue up front.
Good luck with you deceicion....check back to the other thread i posted in a while i'l lpost pics and update it as i get started on mine mannyh |
|
|
|
Re: "The New" AreoWorks 50cc Edge
Thanks mannyh for showing me rccanada. Jack does seem to do a good job building. very informative. And yes I really do want to put that 3W55xi in that plane. I know that DA's are taller then the 3W's. But, I have no clue as for the BME. They(BME) don't give any specs, as to the actual size of the motor. If you can get a measurement of the center shaft, to the top of the head of the BME. That would be great. I did ask Jack, But with the motor in the plane already, that might be tuff.
Thanks. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
EXTREME FLIGHT 50CC EDGE 540T AND CAP!!!! | ULTIMATE1 | What's Hot | 279 | 06-30-2014 04:43 PM | |
50cc Edge ARC? | MX304 | General Discussion | 6 | 07-31-2009 06:48 AM | |
X-Treme Composite 2.6 Edge or Extreme Flight 110" Yak | IFlyEm | General Discussion | 1 | 09-29-2008 06:17 PM | |
which 50cc Edge | yaks | Airframes and Kits | 12 | 05-09-2007 10:50 AM | |
BME Edge 540 / BME 50cc??? | RappyMan | General Discussion | 8 | 01-02-2006 11:21 PM |