|
|
USA, OH, Aurora
Joined Jan 2006
30,070 Posts
|
Need assistance with an MT ENGINE? ask HERE!
I'd like to welcome MT Engines USA.
They sell the MT-57CS, the MT-50, as well as canister/header sets. Check out their website at www.mtenginesusa.com if you have any questions regarding these motors or canisters please ask them here! Again WELCOME MT ENGINES USA! |
|
|
|
China
Joined Jun 2006
417 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
Hello IFLYJR , The biggest prop for MT-57 are 24-10. so you can use 23-8 zoar to break in . keep it in mid rang rpm like 4000 and do not too learn the needle . better use 35:1 oil mix to do the break in .
|
|
|
China
Joined Jun 2006
417 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
Hi Al Lewis
welcome to MT support fourm . if you have anythings need to know about MT engines or caniter muffler system, let us know. happy to answer your question . Tomy |
|
|
|
Re: Need assistance with an MT ENGINE? ask HERE!
Hi Tomy,
I saw a picture of a muffler, but I can not remember where I saw it. It was a pits style cannister that was attached to the bottom of the motor box and was connected to the motor with a Flex header. Could you post that picture again please. When do you think it might be available ? |
|
|
USA, OH, Aurora
Joined Jan 2006
30,070 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
A pilot RC 30% Extra 260 using an MT-57 and the flex header and cannister is located here:
https://www.flyinggiants.com/forums/...260-build.html |
|
|
China
Joined Jun 2006
417 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
looks great. cant wait to see it going to sky !
|
|
|
|
Re: Need assistance with an MT ENGINE? ask HERE!
That is very nice.....But thats not what I was asking for.
The one I am asking about looks like an inverted PITTS wrap around muffler. Only the muffer was bolted under the engine box or to the firewall and attached to the motor with a Flex header. The reason I ask is, I am going to put together the New Aeroworks 50cc Ultimate 20-300. It does not have a cannister tunnel. I could use a regular Pitts wrap around, but I want to try and cut as little of the cowl as possible. Thanks |
|
|
|
Re: Need assistance with an MT ENGINE? ask HERE!
This pitts muffler....
https://www.flyinggiants.com/forums/...tml#post486977 or here https://www.flyinggiants.com/forums/...tml#post512900 Is this Pitts muffler going to become available ? |
|
|
China
Joined Jun 2006
417 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
the pitts muffler will later than tuned pipe .
|
|
|
|
Re: Need assistance with an MT ENGINE? ask HERE!
Tomy,,got a 88" 30% Extra from Pilot with your MT 57 engine.I am now looking to buy new electronics for this plane,and need to know if this engine MUST operate on 6.0 volts exactly,,or can the module handle more volts,as with the DA engines? Just needing to know if I need a regulator for this battery pack,please advise?? Thanks!
|
|
|
China
Joined Jun 2006
417 Posts
|
Re: Need assistance with an MT ENGINE? ask HERE!
Hi , from the RCEXL manual . 6.0V are ok. even some one try use 2 cell lipo and it ok, buy we still recommend 4 or 5 cell package up to 6.0V
Tomy |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
Gas engine tuning for newbies.... | Pro1Foam | Gas Engines | 924 | 10-26-2022 06:42 AM | |
Gas engine break-in procedure... | Mark Davis | Gas Engines | 293 | 09-19-2018 09:41 PM | |
Walbro carb Resetting | suprafly777 | Gas Engines | 16 | 10-13-2011 01:24 PM | |
YS engine questions. | Bamm-o | Nitro Power | 3 | 12-15-2008 10:54 AM | |
Gas engine test bench | Kiwi | General Discussion | 4 | 01-28-2008 06:40 AM |